McIntosh C500C Owner's Manual download pdf (Page 17)

Figure 7

The following listings indicate the Setup Menu Mode (Con-

troller or Preamp), Menu Name, Default Setting and the

page number for instructions on how to change a setting.

Default Settings

Menu Function Name Setting Page No.

Control Version (C500 Firmware) _ . _ _ 17

Control Display (Brightness) 7 17

Control Remote (Control) HR061 17

Control Meter (Illumination) ON 18

Control Volume (Display) Percent 18

Control Trigger A Lvl (Rear Panel Jack) 5V 18

Control Trigger B Lvl (Rear Panel Jack) 5V 19

Control Triamp (Balanced Outputs) OFF 18

Control D/A Ctrl (MDA1000) OFF 19

Preamp Input 3 (Title of Inputs) TUN 20

Preamp D Port (Assignment to Input) Note 2 20

Preamp Trim (Input Source Level) 0.0 21

Preamp Trigger (Input Source) -- 22

Preamp ACC Control (Remote Con.) -- 22

Preamp LPROC (Listen Processor) NONE 23

Preamp RPROC (Record Processor) NONE 23

Preamp MM (Phono Capacitance) 50PF 24

Preamp MC (Phono Resistance) 25 OHM 24

Preamp Passthru (Multichannel) OFF 24

Notes: 1. Charts on page 25 allow for recording any changes

made to the default settings.

2. The D. Port default assignment is the same as the

C500 Controller Rear Panel Data Port Labeling.

Display Brightness

The Front Panel Alphanumeric DISPLAY Brightness may

be varied from a setting of 1 (Dim) to 7 (Bright). Follow the

steps below for reducing the Display Brightness.

1. Press the SETUP Push-button once to access the Setup

Controller Mode unless the C500C is already in the

Setup Controller Mode.

2. Rotate the MENU Control until the word “DISPLAY

7” appears. Refer to figure 8.

3. Rotate the SELECT 2 Control until the Front Panel Al-

phanumeric Display indicates “DISPLAY 5” or the de-

sired Brightness is achived. Refer to figure 9.

4. If no other adjustments are to be made at this time,

press the SETUP Push-button to exit the Setup Control-

ler Mode or proceed to the next desired Setup Control-

ler Mode for adjustment.

Figure 9

Firmware Version

The C500 functionality is controlled by internal software

that is know as Firmware. The Version of the Firmware in

the C500 can be identified at any time by utilizing the Setup

Controller Mode.

1. Press the SETUP Push-button once to access the Setup

Controller Mode.

2. Rotate the MENU Control until VERSION 1.0 or

higher appears. Refer to figure 7.

3. The number after the character V is the Firmware num-

ber.

Figure 8

Setup

7. To exit from the Setup Preamp Mode press the SETUP

Push-button, the LED above the SETUP Push-button

will extinguish and the Front Panel Display will revert

back to its normal display. Refer to figure 3.

4. If no other adjustments are to be made at this time,

press the SETUP Push-button to exit the Setup Control-

ler Mode or proceed to the next desired Setup Control-

ler Mode for adjustment.

Remote Control

The C500 Preamplifier default setting for remote control

operation is for the supplied McIntosh HR061 Remote Con-

trol. The setting may be changed to allow the C500 to work

with the legacy HR054 Remote Control by performing the

following steps:

1. Press the SETUP Push-button once to access the Setup

Controller Mode unless the C500C is already in the

Setup Controller Mode.

2. Rotate the MENU Control until the words “REMOTE

HR061” appears. Refer to figure 9A.

Figure 9A

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 39 40

Comments to this Manuals

No comments

McIntosh C500C Owner's Manual Page 17

Comments to this Manuals

Related products and manuals for Audio amplifiers McIntosh C500C