McIntosh MCD 7005 Operations Instructions download pdf (Page 10)

POWER-1.

Touch the POWER touch-button to turn the player

on. The TRACK, INDEX, TIME, eLAPsed time and

VOLUME indicators will light up in the display area.

Touch POWER again and the player is turned off and

the indicators turn off.

LOAD-2.

Touch the LOAD touch-button and the LED above the

touch-button will illuminate, then after 1 second the

drawer will open. If the drawer is obstructed, it will not

continue to open. Should this happen remove the

obstruction, touch LOAD twice in succession to bring

the drawer fully out.

Hold the disc at the rim and place it label side up, in

the disc drawer.

Close the drawer by touching PLAY, SCAN or LOAD.

Use PLAY if you want to play the complete disc, SCAN

if you first want to preview each track on the disc or

store tracks from it, and LOAD if you want to program

the disc. In each case, the drawer slides in when the

button is touched. If the drawer is obstructed as it

closes, the drawer will come out again after about 3

seconds.

Using LOAD to close the drawer, permits the laser

pen to read the contents list and then display the

number of tracks and the total time encoded on the

disc. After reading the contents list, the MCD 7005 swit-

ches to stand-by mode ready for further instructions.

The DAMAGED DISC/MUTE indicator remains lighted

until play begins. If the light remains on and the disc

refuses to play, make sure that the disc is properly in

the drawer and label side is up.

To close the drawer when it is empty touch the

LOAD button. The DAMAGED DISC/MUTE sign will

light. To prevent the entry of dust, do not leave the

drawer open.

Opening the drawer during play, will stop the disc.

PLAY-3.

To play the complete disc, close the drawer by

touching PLAY. After the contents list on the disc has

been read, the number of tracks on the disc will be

displayed on the track indicator. When play begins,

elapse playing time is displayed and the eLAPsed in-

dicator lights.

To go back to the beginning of a track while it is play-

ing, touch PLAY. The track is then repeated from the

beginning. When all the tracks have been played, the

track indicator, the total elapsed time and the DAMAG-

ED DISC/MUTE indicator will light. All indicators except

the volume display turn off.

VOLUME-4.

Volume may be adjusted by using the VOLUME or

VOLUME on the front panel or on the remote con-

trol. Adjustment of the volume is performed by an elec-

tronically switched precision ladder attenuator.

The Mclntosh electronic precision ladder attenuator

adjusts volume by C

MOS transistor switches that select

the right combinations of highly accurate deposits of

resistive material for the volume programmed.

The entire range of volume adjustment is 66 dB in 2

dB increments. Left and right tracking is controlled to a

fraction of a dB. Because there aren't any moving parts,

the volume adjustment cannot generate noise or

misalignment. Unlike ordinary electronic volume con-

trols, the Mclntosh precision ladder attenuator supports

the distortion-free, low-noise performance of the MCD

7005.

The VOLUME indicator in the message center is a 10

segment display. As volume is increased, more

segments are lighted to indicate relative volume.

SCAN-16.

The first 10 seconds of each track will be played

when the SCAN touch-button is used to initiate play. As

each track is previewed the SCAN indicator, the TRACK

number and the eLAPsed TIME is displayed.

When the tracks have been previewed, the SCAN in-

dicator turns off, the laser pick-up returns to the beginn-

ing of the first track, the total number of tracks and the

total time will be displayed in the message center.

If, before you have previewed all tracks, you decide

to listen to all of the remaining tracks on the disc, touch

PLAY.

The

SCAN

indicator

will

go off and the

remaining

tracks will play in their entirety, beginning with the

track indicated in the message center.

Any track can be entered in the memory for later

playing while using SCAN. For each wanted track,

touch STORE while the track is playing and the TRACK

will be inserted in the memory. The player will preview

the next track and the indicator for that track will be

displayed.

When all tracks have been previewed, SCAN will go

off. To listen to the stored program, touch PLAY And

the disc will play the stored tracks in the sequence

selected.

OPERATION

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16 17

Comments to this Manuals

No comments

McIntosh MCD 7005 Operations Instructions Page 10

Comments to this Manuals

Related products and manuals for CD players McIntosh MCD 7005